Hi all,
I've been experimenting with Archipelago, and overall it kinda works ok (spawns a lot of tree/leaves stuff floating in the air though, and the sea-bed is riddled with floating sand) but for the life of me I can't seem to get the dirt ridges gone... I've tried all the variations on mud flow I could find in various posts, no dice.
Has this changed for 0.4.14? Am I being dumb?
On that note: is there maybe a way to get islands with a lot of sea in v7?
TIA!
FOSS gamedev and creative worlds
This is a mostly frozen copy of the Minetest forums through 2017. If you know phpBB3 and would like to host any G-rated forum here, you can email: me@minetest.org If the email doesn't work, find out who's taken over Final Minetest from OldCoder and email them to get write access or an admin account.
I should have set this up years ago. But it's no tale of woe.
Whether the temperature is high or low, regardless of cold winds blow,
away we go like Edgar Allan Poe, on now with the show. BTW rhymes are welcome.
Mud flow? / mapgen
7 posts
• Page 1 of 1
- KzoneDD
- Member
- Posts: 52
- Joined: Wed Sep 17, 2014 09:29
- KCoombes
- Member
- Posts: 278
- Joined: Thu Jun 11, 2015 23:19
- In-game: Knatt or Rudilyn
Re: Mud flow? / mapgen
KzoneDD wrote:( viewtopic.php?id=8386 )
From your link:
For use with mapgen V6 and these settings in .conf:
- KzoneDD
- Member
- Posts: 52
- Joined: Wed Sep 17, 2014 09:29
Re: Mud flow? / mapgen
And as I stated: those don't remove the dirt ridges...
Re: Mud flow? / mapgen
Did you try:
mgv6_spflags = jungles, biomeblend, nomudflow, snowbiomes, noflat, trees
However i don't recommend using this mod now as it adds mod snow nodes, mgv6 now has built-in snow biomes, so bugs are likely.
In mgv7 you can lower the terrain to get more sea, use these in .conf (or advanced settings):
mgv7_np_terrain_base = 4, 70, (600, 600, 600), 82341, 5, 0.6, 2.0
mgv7_np_terrain_alt = 4, 25, (600, 600, 600), 5934, 5, 0.6, 2.0
The first number in both is the average land level, reduce the first numbers by the same amount and tune this amount to your preference. Suggested value to start with: -24 for both.
mgv6_spflags = jungles, biomeblend, nomudflow, snowbiomes, noflat, trees
However i don't recommend using this mod now as it adds mod snow nodes, mgv6 now has built-in snow biomes, so bugs are likely.
In mgv7 you can lower the terrain to get more sea, use these in .conf (or advanced settings):
mgv7_np_terrain_base = 4, 70, (600, 600, 600), 82341, 5, 0.6, 2.0
mgv7_np_terrain_alt = 4, 25, (600, 600, 600), 5934, 5, 0.6, 2.0
The first number in both is the average land level, reduce the first numbers by the same amount and tune this amount to your preference. Suggested value to start with: -24 for both.
- KzoneDD
- Member
- Posts: 52
- Joined: Wed Sep 17, 2014 09:29
Re: Mud flow? / mapgen
Thanks! This is great info. I'll try your second method. :)
- KzoneDD
- Member
- Posts: 52
- Joined: Wed Sep 17, 2014 09:29
Re: Mud flow? / mapgen
Another thing: I noticed it generates a lot of areas with cave air, do these serve a function?
7 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 16 guests